AeGIS NPB9000 SeriesInstallation and Programming ManualPACH & COMPANY 941 Calle Negocio Phone: 1-888-678-7224www.pach-co.com San Clemente, CA 926
written authorization from Pach and Company Technical Department, with such authorization given only to manufac-turer approved dealer/installers.4. Un
7. Return Merchandise Authorization (RMA) numbers will not be issued to the end-user consumers. Consumers must contact their selling dealer-installer
Chapter 2INSTALLATION 2.1 System’s WiringA proper installation of the AeGIS system is very essential. You MUST follow the installation procedures, blo
Pach and Company Chapter 2 Page 5AeGIS NPB9000 Series INSTALLATION 05/01/0211111312214MAIN RELAY CONTROL PANELMS79012 - MS79120EXPANSION RELAY PANELMX
GROUNDINGGrounding the AeGIS 9000NC, MS79xxx and MX79xxx steel enclosure are essential. Please comply with all local ordinances and industry standard
• Two Conductors, 18-gauge shielded stranded must be used for communication. Ground only one end of the shielded to the earth ground. Use the same ear
• Use two conductors 8-gauge shielded stranded wires.WARNING: The connection is polarity sensitive. Connect the battery (+) terminal to the connector
TENANTS PHONE WIRINGThe RJ71X12 and RJ71X24 are supplied by Pach and Company. The label UP or TOP must at top. Use 22-gaugetwisted wire.RJ71X12has 2-c
Figure 2.4 RS-232 CONNECTOR2.2 Testing and Verifying the InstallationYou must verify your telephone installation by calling every tenant. The easiest
Expansion Relay Panel DIP switches settingThe expansion relay panel is needed to configure more than 120 tenants. Each of the MX79xxx can be used to c
Chapter 3PROGRAMMINGThe AeGIS NPB9000 Series can be programmed locally using the built-in keypad or RS-232 via the Pach and CompanyManagement Softwar
00REPLACE SYSTEM MASTERCODE(Default setting is 0000)Master Code is used to log on toprogramming mode, not to unlockdoor or gate.01CHANGE TALK TIME(Def
FUNCTION CODE LOCAL PROGRAMMING03LOCK OUT COUNT(Default setting is 03 )Minimum setting is 1 and Maximumsetting is 9 .The system will ignore further ke
FUNCTION CODE LOCAL PROGRAMMING06SYSTEM ID(Default setting is 0)07REMOTE ENABLE/DISABLE(Default setting is Enabled)Set the function code to ENABLE ift
Pach and Company Chapter 3 Page 16AeGIS NPB9000 Series PROGRAMMING 05/01/02FUNCTION CODE LOCAL PROGRAMMINGNOT APPLICABLE FOR NO PHONE BILLStep 1 Log
Pach and Company Chapter 3 Page 17AeGIS NPB9000 Series PROGRAMMING 05/01/02FUNCTION CODE LOCAL PROGRAMMINGStep 3 Enter 16 -characters on the first se
Pach and Company Chapter 3 Page 18AeGIS NPB9000 Series PROGRAMMING 05/01/02FUNCTION CODE LOCAL PROGRAMMING12SET TIME AND DATE• Time must be in milit
Pach and Company Chapter 3 Page 19AeGIS NPB9000 Series PROGRAMMING 05/01/02FUNCTION CODE LOCAL PROGRAMMING13TIME ZONE• Time Zone 1-9 is programmableti
Pach and Company Chapter 3 Page 20AeGIS NPB9000 Series PROGRAMMING 05/01/02FUNCTION CODE LOCAL PROGRAMMINGSchedule(s) (ATS) will be notenforced.15AUTO
Pach and Company Chapter 3 Page 21AeGIS NPB9000 Series PROGRAMMING 05/01/02FUNCTION CODE LOCAL PROGRAMMING16REINITIALIZE TIME ZONESCHEDULESIF 0 is ent
TABLE OF CONTENTSLimitations of LiabilityChapter 1. Getting Started ...
Pach and Company Chapter 3 Page 22AeGIS NPB9000 Series PROGRAMMING 05/01/02FUNCTION CODE LOCAL PROGRAMMING17REINITIALIZE AUTO UNLOCKSCHEDULES18REINITI
Pach and Company Chapter 3 Page 23AeGIS NPB9000 Series PROGRAMMING 05/01/02FUNCTION CODE LOCAL PROGRAMMING20NEW TENANT CODEconsists of tenant code, na
FUNCTION CODE LOCAL PROGRAMMING22DELETE A TENANT CODE• To delete, you must know the tenant code (directory code) that youassigned on function code 20.
FUNCTION CODE LOCAL PROGRAMMING24CARD AND CODE(Default setting is 0, for keypadcode or card access)• Optional 26 BIT Wiegand CardReader can be used wi
FUNCTION CODE LOCAL PROGRAMMING27RS-232 or MODEM(Default setting is 1 for MODEM)You may program the system viabuilt-in RS-232 (local) or MODEM(remote)
Pach and Company Chapter 3 Page 27AeGIS NPB9000 Series PROGRAMMING 05/01/02FUNCTION CODE LOCAL PROGRAMMING30ADD KEYPAD ACCESS CODE ANDCARD NUMBER (RAD
FUNCTION CODE LOCAL PROGRAMMING31MODIFY CARD NUMBER (RADIOTRANSMITTER NUMBER)• You must know the keypad accesscode to modify this field.• The keypad a
FUNCTION CODE LOCAL PROGRAMMING32DELETE KEYPAD ACCESS CODEAND CARD NUMBER (RADIOTRANSMITTER NUMBER)• You must know the keypad accesscode to delete thi
FUNCTION CODE LOCAL PROGRAMMING40MASTER CODE MASK(Default setting is disabled)WARNING !!!!!!!!• Master Code cannot be recoveredif Master Code Mask is
FUNCTION CODE LOCAL PROGRAMMING43OPEN DOOR 1 AND DOOR 2 NUMBER (REMOTE ACCESSNUMBER) OR CCTV SWITCH(Default setting is 9 to unlockrelay 1 (door 1) or
How to Extend the Talk Time ... 35How to use
FUNCTION CODE LOCAL PROGRAMMING46DISPLAY SYSTEM INFORMATION 50CLEAR THE EEPROM MEMORYTO FACTORY DEFAULT 78VIEW DIRECTORY AND NAMEStep 5 Select another
FUNCTION CODE LOCAL PROGRAMMINGStep 3 Press # to view the tenant code (directory code), the display showsNNNNNNNNNNNN= tenant nameXXXX= 2-digit, 3-dig
Chapter 4SYSTEM’S OPERATIONHOW TO VIEWTHE TENANT NAME.HOW TO INITIATE ACALL AND UNLOCKTHE DOOR FORVISITOR.Two ways to view the tenant name:1. Press 3
HOW TO EXTEND THETALK TIMEHOW TO USE THE CALL WAITINGHOW TO USE THE DOORMAN ORMANAGER PHONEHOW TO USE THE KEYPAD ACCESS CODEHOW TO USE THECARD ACCESS
HOW TO USE THECOMBINATION OFCARD ACCESS ANDKEYPAD ACCESS CODEHOW TO USE THEALARM TELEPHONENUMBERRELAY 2 MODESStep 1 Function Code 24 must set to 1Step
HOW THE DOORSENSOR OR SHOCKSENSOR OPERATESA Shunt (Mode 2)Relay 2 and relay 1 are opened and closed simultaneously. You can use this feature forthe fo
seconds. The authorized person will hear continuous beeps when the phone is answered. The display showsThe scenarios above are valid until the problem
HOW TO ADJUST THESPEAKER ANDMICROPHONE VOLUMEHOW TO ADJUST THELCD DISPLAYHOW TO ADJUST THEPULSE SENSITIVITYHOW TO CHECK THENUMBER OF TENANTSPROGRAMMED
Chapter 5TROUBLE SHOOTING GUIDENO AUDIO WHENKEY(S) IS PRESSEDTHE VISITOR CAN'THEAR THE TENANTFROM THE SYSTEMBUT THE TENANT CANHEAR THE VISITORTHE
THE LCD SHOWSEIGHT SQUARES ORUNDERLINESTHE VISITOR CAN'TPLACE A CALL TO ATENANT OR TENANTSTHE VISITOR HEARS ARADIO STATION ONTHE MAIN LOBBYCONTRO
LIMITATIONS OF LIABILITYThis manual is subject to change without notice.Pach and Company is not liable for any errors that might occur from use of thi
The technical support team at Pach and Company are highly trained and committed to providing you with the best in support and repair services. Our Ser
GENERAL FCC REQUIREMENTSThis equipment complies with Part 68 of the FCC rules. Located on the back of your AeGIS system isa label that contains, among
AeGIS NPB9000 Series QUICK REFERENCELOCAL PROGRAMMING1) PRESS 0 AND # SIMULTANEOUSLY THEN RELEASE, the display screen stops scrolling (If the display
Chapter 1GETTING STARTED1.1 IntroductionPach & Company thanks and congratulates you on the purchase of your AeGIS NPB9000 Series Telephone Access
Technical Specifications:AeGIS NPB9000 SeriesPower Input: 12 VAC 40 VA (supplied) or 12 VDC 40VA UL Listed TransformerCurrent Consumption: AeGIS 9000N
• Warranty Card with unit serial number.1.4 Limited WarrantyPach and Company new products are warranted to be free of defects in material or workmansh
NEW PRODUCT WARRANTY EXCEPTIONWIEGAND CARD, KEYFOB AND TRANSMITTERPach and Company warrants the wiegand card, clam, and keyfob to be free of defects i
Commentaires sur ces manuels